Modelling and Simulation of Mho Type Distance Relay for High Voltage Transmission Line Protection Using MATLAB Software
DOI:
https://doi.org/10.12962/j25796216.v3.i2.91Abstract
Transmission lines are an important part of a power system. Transmission lines have high power transmission capacity and they are prone to faults of larger magnitudes. Various faults occur in transmission lines. Therefore, protection relays are necessary to protect transmission lines. The purpose of protection system is to interrupt the faulty section from the healthy section because the fault currents may damage the electrical equipments. One of the protection relays is distance relay and it is mainly used in transmission line. Sometimes these relay are used for backup protection. Distance relays for determining the impedance need the voltage and current. Transmission lines are typically protected by distance protection relay. Distance relays are considered of high speed class and can provide transmission lines. Nowadays, numerical distance relays have been used instead of using electromechanical and static distance relays. The proposed model was verified under different tests such as single line to ground (L-G) fault, double line to ground (L-L-G) fault, line to line (L-L) fault and three phase (L-L-L) fault. SimPower System was used for modelling and simulation of distance relay, transmission lines and faults. The simulation results were obtained from MATLAB software shows the feasibility of analysis of transmission line protection with mho type distance relay for single line to ground fault, double line to ground fault, line to line fault and three phase fault at different location of transmission lines. The difficulties understanding on operation of distance relay can be cleared by using MATLAB/SIMULINK software.
Keywords: distance relay, double line to ground (L-L-G), line to line fault (L-L), MATLAB/SIMULINK, single line to ground fault (L-G), three phase fault (L-L-L).
References
DibyaDarshiniM0hanty, AshwinSharwin Sharma, AshutoshVarma, “Performance assessment of distance relay using matlab,” International Journal of Engineering Research and Technology (IJERT), vol. 2, 2 Issue 12, December. 2013.
J.N.Rai,Aquib Jahangir, IlamHoque, “Digital simulation of distance relay for long transmission line,” 2017 4th IEEE Uttar Pradesh Section International Conference on Electrical, Computer and Electronics (UPCON), GLA University, Mathura,Oct 26028, 2017.
PurraSaiKiran, P.Ramchander, “Modeling and performance analysis of mho relay in matlab,” International Journal and Magazine of Engineering, Technology, Management and research, Volume No:2(2015), Issue No:1(January), January 2015.
Mr.Kunal, K.Joshi, Prof. M.R.Hans, “Development of mho type distance relay for protection of long transmission line using matlab/simulink environment,” International Journal of Engineering Research and Technology (IJERT), vol. 5, Issue 04,April.2016.
M.Rambabu, M.Venkatesh, J.S.V.SivaKumar,T.S.L.V.AyyaRao, “Three zone protection by using distance relays in simulink/matlab”, International Research Journal of Engineering and Technology (IRJET), vol. 02, Issue. 05, Aug. 2015.
JayantLamture, A.P.Vaidya, “Development of distance relay in matalb,” International Journal of Advanced Computational Engineering and Networking, ISSN:2320-2016, vol. 3, Issue 9, Sept. 2015.
Downloads
Additional Files
Published
Issue
Section
License
Copyright
Submission of a manuscript implies that the submitted work has not been published before (except as part of a thesis or report, or abstract); that it is not under consideration for publication elsewhere; that its publication has been approved by all co-authors. If and when the manuscript is accepted for publication, the author(s) still hold the copyright and retain publishing rights without restrictions. Authors or others are allowed to multiply article as long as not for commercial purposes. For the new invention, authors are suggested to manage its patent before published. The license type is CC-BY-NC 4.0.
Disclaimer
No responsibility is assumed by publisher and co-publishers, nor by the editors for any injury and/or damage to persons or property as a result of any actual or alleged libelous statements, infringement of intellectual property or privacy rights, or products liability, whether resulting from negligence or otherwise, or from any use or operation of any ideas, instructions, procedures, products or methods contained in the material therein.
