Design and Implementation of Protection Relay 3 Phase Induction Motor
DOI:
https://doi.org/10.12962/j25796216.v3.i2.99Abstrak
Damage to the electrical components will inevitably occur, it could be caused by several factors that influence it starting from inside and outside the system. 3 phase induction motor is the most commonly used in the industry, but often also has problems such as over current and over heat on the motor. The disturbance if left unchecked can cause fatal damage to the motor. therefore, a relay safety system has been made which utilizes a microcontroller controller to protect the 3 phase induction motors. This safety relay is designed differently than conventional safety relays used by industry in general, this safety relay is designed based on the microcontroller control and is accompanied by setting and resset facilities respectively to display on the LCD via Push Botton buttons. As such, 3 phase induction motors are protected from severe damage caused by interference with the mesh source. It is expected that by making this safety relay can reduce the value of damage to the 3 phase induction motor.
Keywords: microcontroller, overcurrent, overheat, three phase induction motor.
Referensi
Aji, Zaenal Panutup “Teknik Pengukuran Temperature Belitan Motor Induksi Menggunakan Metode Resistansi”, Balai Riset dan Standarisasi Industri Surabaya, 2014.
Wahjono Endro “Rancang Bangun Relay Pengaman untuk Mengatasi Gangguan Motor Induksi 3 Phase”, Jurusan Teknik Elektro Industri, PENS, 2014.
Tukananto Andri “Rancang Bangun Sistem Proteksi Arus Lebih Motor 3 Fasa Dengan Timer Start dan Trip”, Jurusan Teknik Elektro Industri, Fakultas Teknik Universitas Tanjungpura, 2015.
Sholeh Moh. “Rancang Bangun Sistem Kontrol dan Proteksi Motor Listrik Terhadap Panas (Overheating) serta Peringatan Dini terhadap Gangguan Tegangan dan Arus Berbasis AtMega 328”, Jurusan Teknik Elektro, Universitas Islam Lamongan, 2018.
Standar NEMA (The National Elektrical Manufacture Association) tentang Insulation Class suatu electro motor.
Spesifikasi Three-phase Inductioan Motor with Slip-Ring Rotor
Azizi, Alvian Kurnia “Rancang Bangun Modul Praktikum Buck Boost Converter Menggunakan Kontroller PID Untuk D3 Teknik Listrik Industri” Politeknik Negeri Madura, 2016.
Data Sheet salah satu Produsen Thermistor
MURATA PartNo. NXFT15XH103).
Standar Nasional Indonesia (SNI) IEC 60335-1 : 2009, Badan Standarisasi Nasional, Jakarta-Indonesia, 2009.
Y. Yorozu, M. Hirano, K. Oka, and Y. Tagawa, “Electron spectroscopy studies on magneto-optical media and plastic substrate interface,” IEEE Transl. J. Magn. Japan, vol. 2, pp. 740–741, August 1987 [Digests 9th Annual Conf. Magnetics Japan, p. 301, 1982].
M. Young, The Technical Writer’s Handbook. Mill Valley, CA: University Science, 1989.
##submission.downloads##
Diterbitkan
Terbitan
Bagian
Lisensi
Copyright
Submission of a manuscript implies that the submitted work has not been published before (except as part of a thesis or report, or abstract); that it is not under consideration for publication elsewhere; that its publication has been approved by all co-authors. If and when the manuscript is accepted for publication, the author(s) still hold the copyright and retain publishing rights without restrictions. Authors or others are allowed to multiply article as long as not for commercial purposes. For the new invention, authors are suggested to manage its patent before published. The license type is CC-BY-NC 4.0.
Disclaimer
No responsibility is assumed by publisher and co-publishers, nor by the editors for any injury and/or damage to persons or property as a result of any actual or alleged libelous statements, infringement of intellectual property or privacy rights, or products liability, whether resulting from negligence or otherwise, or from any use or operation of any ideas, instructions, procedures, products or methods contained in the material therein.
